Ram 1500 & 2500 Diagnostic Guide

By Roger Holden. Updated November 10, 2026. Researched from manufacturer bulletins published by NHTSA, not a diagnosis of your vehicle. Part of the RateThisPro Automotive Diagnostic Center.

Covers: Selected 2013 Ram 1500 4.7L/5.7L and Ram 2500 5.7L applications; 2019 Ram 1500 5.7L eTorque; 2013–2015 and 2018 Ram 2500 6.7L Cummins diesel. Not comprehensive model-year coverage.

Before diagnosing a Ram truck, identify the engine and platform as well as the badge on the fender. The bulletins in this guide distinguish the DS Ram 1500 from the DT Ram 1500, limit some procedures by engine sales code and build date, and separate gasoline EVAP work from Cummins diesel exhaust treatment. A code number does not erase those differences. For example, published P0456 procedures include software updates, but the 2019 eTorque bulletin also calls for a small-leak verification test. That is a reason to test the truck, not a reason to assume every EVAP warning is software.

This guide summarizes five manufacturer technical service bulletins published on NHTSA's website, plus a manufacturer communication explaining the Security Gateway. The summaries are research-based, not hands-on testing or a diagnosis of your vehicle. A bulletin applies only to its listed vehicles and conditions, and historical instructions may have later revisions. Use the material to save useful evidence, choose a shop with the necessary functions, and ask which measurement supports the proposed repair. Publication alone does not establish that your truck needs the repair or qualifies for warranty coverage.

Where to plug in a scanner

Start looking below the steering wheel in the driver's footwell. For vehicles subject to its connector provision, California's 13 CCR 1968.2(g)(2.1.1) requires a driver's-side footwell location no higher than the bottom of the steering wheel at its lowest adjustment. The connector may not be on or in the center console, and a crouched technician entering from the driver's side must be able to identify its location. The following provision requires a labeled, hand-removable cover if it is covered. This is a sourced search area, not confirmation of the precise bracket position on every Ram configuration; consult the exact vehicle's documentation if the connector is not apparent.

What a scanner needs to do on a Ram 1500 & 2500

Manufacturer bulletins worth knowing

TSB 18-001-14: gasoline P0456 PCM update

2013 Ram 1500 and Ram 2500; bulletin also lists Ram 3500

Chrysler published a bulletin for 2013 DS Ram 1500 trucks with the listed 4.7L or 5.7L engines built on or before July 18, 2013, and listed 5.7L DJ Ram 2500 applications built on or before June 20, 2013. It addresses P0456 with PCM reprogramming and directs technicians to record and repair other codes as necessary first. Engine sales codes and the separate build cutoffs matter.

Codes listed: P0456

Read the bulletin

TSB 18-076-20 Rev. A: 5.7L eTorque PCM updates

2019 Ram 1500

FCA published a bulletin for 2019 DT Ram 1500 trucks with the 5.7L Hemi MDS VVT eTorque engine, sales code EZL, in the listed markets. It describes PCM updates for specified codes and symptoms, but explicitly requires the wiTECH Small Leak Verification Test if P0456 is present. The bulletin supersedes the earlier 18-076-20 publication.

Codes listed: P0339, P0335, P258B, P0456

Read the bulletin

TSB 18-088-15: Cummins P20EE diagnosis

2013–2015 Ram 2500 and Ram 3500 pickups

FCA published a bulletin for the listed pickups with the 6.7L diesel, sales code ETK, to verify DEF-system operation and replace the SCR catalyst only if the procedure directs it. The checks include DEF leaks or restrictions, a complete dosing-flow test, and fluid contamination. A leak, an out-of-range flow result, or contamination sends the technician to other diagnosis or repair rather than automatically to catalyst replacement.

Codes listed: P20EE

Read the bulletin

TSB 25-003-14: DEF-related inducement strategy

2013–2015 Ram 2500; bulletin also lists 3500 and 4500/5500 applications

Chrysler published an information bulletin for the listed 6.7L Cummins applications with SCR, sales codes ETK and XAL, explaining DEF-quality-related inducement and its warning messages. It identifies P207F as Reductant Quality Performance and P1C70 as SCR Error Detected – Engine Disabled. Its clearing instructions concern the system after the underlying DEF-quality repair, not a substitute for that repair.

Codes listed: P207F, P1C70

Read the bulletin

TSB 18-080-22: 2018 Cummins ECM/PCM updates

2018 Ram 2500 and Ram 3500 pickups

FCA published a software-update bulletin for North American 2018 Ram 2500 and 3500 pickups with the 6.7L I6 Cummins Turbo Diesel, sales code ETK. Its longer code list includes these examples and directs ECM/PCM reprogramming with current software. This is a calibration check for matching vehicles, not evidence that every listed code on every Cummins truck has a software-only cause.

Codes listed: P064F, P229F, P207F, P2509, P0401, P2201, P0128

Read the bulletin

Cummins: check DEF delivery before condemning the SCR catalyst

The P20EE procedure in bulletin 18-088-15 is a useful example of diagnostic order. It first checks hoses and connections for leaks or restrictions, then measures DEF delivery with a complete timed test, then checks the fluid for contamination. Only the appropriate results lead farther down its catalyst-replacement path. The bulletin also warns against replacing the DEF injector simply because dry deposits appear to block its holes or residual fluid collects during testing.

Keep the DEF/SCR complaint separate from a DPF regeneration request. These opened Cummins bulletins support specific dosing, calibration, and inducement procedures; they do not make regeneration the default response to P20EE or P207F. A shop should explain which current procedure applies and what test result it is following. This guide likewise does not infer glow-plug service from any of the listed codes.

Bulletin 25-003-14 describes a DEF-system countdown that can lead to a 5-mph maximum-speed message. Record the exact wording and remaining distance and arrange diagnosis rather than treating the message as an ordinary reminder. The bulletin also notes that P1C70 may remain after P207F was previously cleared. That is another reason to preserve the original scan history and tell the technician about earlier code clearing.

A sensible diagnostic order

  1. Record the VIN, model year, engine, platform, build date, mileage, and exact warning messages. Distinguish DS from DT where relevant and have the shop verify engine sales codes. The 2013 gasoline and 2019 eTorque procedures do not cover every truck wearing the same Ram 1500 badge.
  2. Save all available codes, their statuses, freeze-frame data, and readiness information before erasing anything. Tell the shop whether another person previously cleared codes or installed software. The inducement bulletin specifically describes a situation in which an earlier code may have been cleared before the truck arrives.
  3. Check open safety recalls by VIN at https://www.nhtsa.gov/recalls. Separately review manufacturer communications and ask the shop to confirm the current bulletin revision and exact applicability. A recall search is not a substitute for checking a TSB's engine, market, build-date, and symptom restrictions.
  4. Address companion faults in the order required by current service information. The P0456 and P20EE bulletins tell technicians to record and repair other relevant codes before proceeding. Ask for that complete diagnostic picture rather than authorizing a catalyst, injector, or EVAP component solely from one code description.
  5. Perform the vehicle-specific verification test. For the listed 2019 eTorque application, that includes the small-leak verification test when P0456 is present. For the listed 2013–2015 Cummins P20EE procedure, it includes DEF delivery and contamination checks. Do not substitute visual deposits or a generic scanner label for the required result.
  6. Complete the applicable software, repair, and post-repair verification procedure. Confirm SGW authentication if commands are blocked on an equipped truck, and use the current service instructions for inducement recovery after repair. Retain the test results and post-repair scan so a cleared light is not the only record of the work.

Record stored, pending and permanent codes and available freeze-frame data before clearing anything. Clearing codes does not fix the fault; it can erase useful evidence and reset emissions readiness monitors.

Frequently asked questions

Does P0456 always mean a physical leak needs a new part?

No such conclusion follows from these bulletins. The 2013 publication describes a PCM update on narrowly listed gasoline applications, while the 2019 eTorque bulletin also requires a small-leak verification test. Identify the exact truck and test it before choosing between a repair and a software procedure.

Does P20EE prove the Cummins SCR catalyst has failed?

Not on the basis of bulletin 18-088-15 alone. Its procedure checks DEF leaks, delivery, and contamination before reaching catalyst replacement. Results outside its requirements send the technician to other diagnosis or repair, so the code is not an automatic catalyst purchase order.

Why can a scanner read information but fail to run a test?

On an SGW-equipped vehicle, authentication may be relevant. The opened manufacturer communication says the gateway allows view-only aftermarket access but authenticates requests for operations. Confirm the tool's authorized access and exact function coverage before interpreting an unavailable command as a failed vehicle module.

Can clearing P207F remove the DEF speed restriction?

Do not rely on clearing a code as a repair. Bulletin 25-003-14 explains inducement recovery after DEF-quality repairs and notes that P1C70 may remain when P207F was cleared earlier. Preserve the warning messages and have the shop follow the current recovery procedure for the vehicle.

Should every 2018 Cummins truck with a listed code receive only software?

No. Bulletin 18-080-22 is an application-specific update, not a universal diagnosis. Have the shop verify the engine, market, existing calibration, other faults, and current service instructions. A code's appearance in a software bulletin does not by itself rule out a separate hardware or wiring problem.

Sources

Other vehicle diagnostic guides