Ford F-150 & Super Duty Diagnostic Guide
By Roger Holden. Updated November 10, 2026. Researched from manufacturer bulletins published by NHTSA, not a diagnosis of your vehicle. Part of the RateThisPro Automotive Diagnostic Center.
Covers: Selected 2018, 2019, and 2021 F-150 EcoBoost applications; 2011–2012 and 2015 F-Super Duty with the 6.7L Power Stroke diesel. This is not comprehensive coverage of every engine, trim, or model year.
Start a Ford truck diagnosis with the exact engine, model year, build date, and complete code list—not a part suggested by one code. Ford's published examples show why that matters. A narrowly defined 2018 2.7L EcoBoost condition calls for a fuel-pressure check before injector replacement; a 2021 2.7L bulletin addresses PCM software; and a 2019 Limited high-output 3.5L bulletin connects a power-loss or misfire complaint to the muffler. Similar symptoms can therefore lead to very different service procedures. Treat these examples as reasons to identify the truck carefully, not as a list of parts to buy.
This guide summarizes five Ford technical service bulletins hosted by NHTSA. Each applies only when the vehicle and condition match the bulletin, and Ford warns that these procedures are intended for trained technicians. A bulletin is not proof that your truck has the described defect, and its publication does not establish current warranty eligibility. Use the summaries to organize your scan report and questions for a repair shop. Have the shop check current Ford service information for revisions before performing a historical bulletin's repair.
Where to plug in a scanner
Begin the port search below the steering wheel in the driver's footwell. California's OBD II regulation, 13 CCR 1968.2(g)(2.1.1), places the connector for vehicles subject to that provision in the driver's-side footwell, no higher than the bottom of the steering wheel in its lowest adjustable position. It excludes the center console and requires a location identifiable by a crouched technician entering from the driver's side. A covered connector must have a hand-removable, labeled cover under the following provision. This is a regulatory search area, not a verified mounting position for every F-150 or Super Duty configuration; check the exact vehicle's documentation rather than removing trim on that assumption.
What a scanner needs to do on a Ford F-150 & Super Duty
- Choose a tool that can save the original code report and freeze-frame information before anything is erased. California's regulation requires fault-related freeze-frame storage under specified conditions. For this guide's diagnostic workflow, the useful feature is an export or readable record you can give the technician, rather than a screen that only offers a code description and an erase button.
- For the 2018 2.7L condition in TSB 18-2310, confirm access to Ford fuel-rail-pressure data, including observation after engine shutdown. The bulletin calls for an appropriate Ford scan tool when monitoring pressure. Do not assume that a tool displaying generic engine codes also exposes the particular data and operating conditions required by this procedure.
- Separate code reading from module programming. TSB 18-2109 names Ford Integrated Diagnostic System, or IDS, and Ford J2534 Diagnostic Software, or FJDS, for its 2015 diesel PCM update. Those names support this specific historical procedure; they are not a promise that one software package covers every truck discussed here. Ask the shop to confirm the current programming method for your VIN.
- Check for the exact diesel reset function, not merely an advertising claim of diesel support. TSB 13-6-24 requires clearing the NOx sensor adaptive learn tables and explicitly says PCM reprogramming does not reset them. A tool that reads the codes, or even installs software, has not necessarily completed that separate service step.
- Match additional functions to the actual job. The early 6.7L procedure uses specific exhaust-gas-temperature data if forced-idle recovery is needed. Ask separately about enhanced module access, transmission relearns, TPMS work, and DPF service regeneration; these bulletins do not establish universal coverage for those functions. Do not buy a scanner on the assumption that one supported Ford service function guarantees all the others.
Manufacturer bulletins worth knowing
TSB 18-2310: 2.7L EcoBoost injector diagnosis
2018 F-150
Ford published a bulletin for some 2018 F-150 trucks with the 2.7L EcoBoost, built on or before July 12, 2018, with more than 500 miles and specified PCM codes. It requires checking fuel-rail pressure after shutdown before directing injector replacement; if that test does not meet the bulletin's condition, it sends the technician back to normal diagnosis. This bulletin supersedes 18-2270 because the earlier procedure was incorrect.
Codes listed: P0300, P0316, P0301, P0302, P0303, P0304, P0305, P0306, P2196, P2198, P0171, P0174, P219A, P219B, P0172, P0175
TSB 19-2286: high-output 3.5L muffler condition
2019 F-150
Ford published a bulletin for 2019 F-150 Limited trucks with the high-output 3.5L EcoBoost, built on or before June 1, 2019, that lack power or misfire, with or without these codes. Ford identifies improperly assembled internal muffler components as a possible cause and provides a measurement-based service procedure. This is not a blanket muffler diagnosis for other F-150 trims or engines.
Codes listed: P0300, P0301, P0302, P0303, P0304, P0305, P0306
TSB 21-2085: 2.7L PCM software
2021 F-150
Ford published a bulletin for some 2021 F-150 trucks with the 2.7L EcoBoost, built on or before March 1, 2021, with an illuminated malfunction indicator lamp and these PCM codes. It says various PCM software parameters may cause the condition and directs PCM reprogramming using the appropriate Ford diagnostic scan tool.
Codes listed: P060B, P0300, P0316
TSB 18-2109: 2015 diesel PCM update
2015 F-Super Duty
Ford published a bulletin for 2015 F-Super Duty trucks with the 6.7L diesel and an illuminated malfunction indicator lamp with these PCM codes. Its action is PCM reprogramming with IDS or FJDS at the specified software level or higher. The bulletin does not direct automatic replacement of a diesel particulate filter, SCR catalyst, or sensor based solely on this code list.
Codes listed: P012F, P207F, P2002, P20EE
TSB 13-6-24: early 6.7L NOx sensor and adaptive reset
2011–2012 F-Super Duty
Ford published a bulletin for some 2011–2012 F-Super Duty trucks with the 6.7L engine, built on or before October 11, 2011, and specified codes. The procedure includes an updated NOx sensor, PCM programming, and a separate reset of NOx sensor adaptive learn tables. It also has additional instructions for specified chassis-cab applications and trucks remaining in forced idle.
Codes listed: P207F, P20EE, P2200, P2201, P2209, P164A, P2A00, P0133
Power Stroke: distinguish software, sensor learning, and regeneration
Do not treat every diesel emissions code as an instruction to add DEF, replace an exhaust component, or force a DPF regeneration. Ford's 2015 bulletin lists P012F, P207F, P2002, and P20EE together but directs a PCM update. That is a useful warning against diagnosing by the name of a system alone. It does not establish that a software update fixes those codes on a different model year or under a different condition.
The early 6.7L bulletin illustrates another distinction: installing a sensor, updating software, and resetting learned values are separate operations. Ford says the NOx adaptive tables are not cleared by PCM reprogramming and must be reset to prevent codes from setting falsely. When reviewing a repair invoice for a matching truck, ask whether the required adaptive reset was completed rather than assuming that 'computer updated' describes the whole procedure.
DPF regeneration and glow-plug diagnosis are outside the verified repair procedures summarized here. Neither a regeneration command nor glow-plug replacement should be inferred from these bulletin lists. The Ford diesel PDFs opened for this guide list codes without supplying their full definitions, so no Ford diesel code glossary is reproduced below. Keep the exact code numbers in your report and have the shop use the current Ford diagnostic description and test sequence for that VIN.
A sensible diagnostic order
- Identify the truck before selecting a procedure. Record the VIN, engine, model year, trim, build date, mileage, warning messages, and the circumstances of the complaint. For these bulletins, details such as Limited trim, a high-output engine, an early build date, or more than 500 miles can determine whether the procedure applies.
- Save the scan evidence before clearing it. Record every available code and its status, freeze-frame data, and readiness information. Note whether the problem happened at idle, under load, or after a previous repair. Freeze-frame storage is part of the OBD regulation; preserving that information gives the technician something more useful than a remembered code number.
- Check open safety recalls by VIN at https://www.nhtsa.gov/recalls. Separately search manufacturer communications and ask the shop to verify the latest Ford bulletin revision. A VIN recall result and a TSB applicability check answer different questions; do not treat an empty recall result as proof that no relevant service bulletin exists.
- Match every bulletin condition before authorizing its repair. For example, the 2018 injector bulletin requires the listed engine, build range, mileage, codes, and pressure-test result. If a condition does not match, follow normal Ford diagnosis rather than stretching the bulletin to fit the complaint.
- Have the technician perform the applicable measurements or software checks before replacing parts. The 2018 injector procedure and 2019 muffler procedure both contain decision points. Ask which test result justified the repair, and retain that result with the original scan report.
- Complete the specified programming, resets, and follow-up checks. On the early diesel application, confirm the separate NOx adaptive reset; where Ford warns of transmission relearning after a reset, ask what to expect. Save the post-repair scan and readiness status so the repair is documented rather than judged only by an erased warning light.
Record stored, pending and permanent codes and available freeze-frame data before clearing anything. Clearing codes does not fix the fault; it can erase useful evidence and reset emissions readiness monitors.
Frequently asked questions
Does P0300 mean my F-150 needs ignition parts?
Not by itself. The opened Ford bulletins associate overlapping misfire-code lists with an injector test, PCM software, and a narrowly defined muffler condition. Those examples do not rule ignition faults in or out; they show why the engine, build date, symptoms, and test results must come before a parts decision.
Can I apply the 2018 injector bulletin to any 2.7L truck?
No. TSB 18-2310 specifies a 2018 F-150, a build date on or before July 12, 2018, more than 500 miles, listed codes, and a pressure-test decision. Ford says to return to normal diagnosis when the required conditions are not met.
Will a PCM update reset the NOx sensor's learned values?
Not in the procedure described by TSB 13-6-24. Ford explicitly requires a separate reset of the NOx adaptive learn tables because PCM reprogramming does not reset them. That statement concerns this bulletin; ask for the current instructions for other model years.
Does a diesel emissions code mean I should request a forced regeneration?
These bulletins do not support that shortcut. The 2015 diesel bulletin directs programming, while the early 6.7L bulletin includes sensor replacement and adaptive learning work. Ask which current diagnostic result makes regeneration appropriate before treating it as the next step.
Does a published Ford TSB guarantee a free repair?
No. The Ford bulletins say warranty limits and policies are not changed by publication and that coverage depends on the applicable warranty provisions. Ask the dealer to check your VIN, mileage, repair history, and current coverage instead of treating a historical bulletin as a repair authorization.
Sources
- Ford TSB 18-2310 — 2018 F-150 2.7L — used for: Build and mileage limits, code list, pressure-test decision, injector procedure, and supersession of 18-2270.
- Ford TSB 19-2286 — 2019 F-150 Limited — used for: High-output 3.5L, Limited trim, build cutoff, power loss or misfire, code range, and muffler measurement procedure.
- Ford TSB 21-2085 — 2021 F-150 2.7L — used for: Build cutoff, code list, possible PCM software cause, programming, and transmission adaptive-strategy notice.
- Ford TSB 18-2109 — 2015 6.7L F-Super Duty — used for: Diesel code list, IDS/FJDS programming, warranty limitations, and transmission relearning notice.
- Ford TSB 13-6-24 — 2011–2012 6.7L F-Super Duty — used for: Build cutoff, code list, NOx sensor replacement, IDS programming, separate adaptive reset, and forced-idle recovery data.
- California OBD II regulation — 13 CCR 1968.2 — used for: Regulated connector location, cover requirements, freeze-frame storage, and diagnostic information requirements.
- NHTSA — Recalls — used for: VIN-based safety recall lookup, separate from bulletin applicability.