How to Choose a Jump Starter for a Diesel Truck
RateThisPro Automotive Research Library reference guide. By Roger Holden. Published November 10, 2026, updated November 10, 2026. Researched from the 12 sources listed below, with no product placements.
The short answer
Choose a diesel-truck jump starter in this order: match the truck's system voltage (diesel pickups with two batteries are still 12-volt, and Ram and Ford both prohibit a 24-volt source), then check the pack maker's stated diesel engine-size rating, its operating and charging temperature limits and its cranking and rest limits. Don't compare packs on peak amps; that number has no industry-agreed definition. Follow your truck's manual for where to connect and wait for the glow-plug or wait-to-start light before cranking.
Key facts
- Higher compression, thicker cold oil and larger cylinders all raise the energy needed to crank an engine, and diesel engines often use two batteries for that reason. [Source 5]
- Interstate says a car battery loses about 35 percent of its strength at 32°F and up to 60 percent at 0°F, while the engine needs nearly twice the power to start. [Source 4]
- Ram's 2019 heavy-duty diesel supplement says the truck has two 12-volt batteries and prohibits any booster source greater than a 12-volt system, including 24-volt sources. [Source 1]
- The same Ram manual warns that a portable starting unit above 12 volts DC can damage the battery, starter motor, alternator or electrical system. [Source 1]
- Ford's 2016 6.7L Super Duty diesel supplement says to use only a 12-volt supply and not to disconnect the disabled truck's battery, which could damage the electrical system. [Source 2]
- For that Ram, the manual specifies the jump post for the positive connection, not the fuses, and a good engine-block ground for the negative, not the discharged battery's negative post. [Source 1]
- The 2016 6.7L Power Stroke has eight glow plugs, one per cylinder, and Ford says to wait until the glow-plug indicator goes off before starting. [Source 2]
- The 2019 Ram 6.7L diesel pre-heats incoming air with an intake heater, and its remote start waits for the Wait To Start light to go out before cranking. [Source 1]
- Cummins says its redesigned 6.7L for 2025 Ram Heavy Duty trucks adds glow plug technology for improved cold starts, so heater type depends on model year. [Source 3]
- Clore Automotive, a jump-starter maker, says peak amps have no industry-agreed definition, so one company's peak-amp value may not equal another's. [Source 7]
- A battery's cold cranking amps (CCA) rating is the current a new, fully charged battery delivers for 30 seconds at 0°F while staying at or above 7.2 volts. [Source 6]
- UL 2743 is the safety standard for portable power packs, including battery packs with a vehicle jump-start function; it is a safety test, not an engine-size rating. [Source 8]
- NOCO rates its 12V GB150 for gas engines up to 9.0 liters and diesel engines up to 7.0 liters; that is the maker's application claim, not a guarantee for every truck and temperature. [Source 9]
- The GB150's published operating range is −4°F to 122°F, but it should only be charged between 32°F and 104°F. [Source 9]
- Duty cycles vary by pack: Clore's JNC770 manual says to let the unit cool 3 minutes if the vehicle doesn't start within 6 seconds, while NOCO allows no more than five attempts in 15 minutes before a 15-minute rest. [Source 11]
- NOCO's GB150 manual says not to jump-start a frozen battery. [Source 10]
Why diesel trucks are harder to jump-start
A diesel engine ignites fuel with compression heat rather than a spark, so it runs a much higher compression ratio than a gas engine of similar size. Turning that engine over takes more current, and the demand climbs in cold weather when the oil thickens. That is why many diesel pickups carry two batteries.
Cold works against you twice. Interstate's figures put a battery's available strength about 35 percent lower at 32°F and up to 60 percent lower at 0°F, while the engine needs close to twice the power to start. A jump starter that handles a gas V8 on a mild day can struggle with a 6.7-liter diesel on a winter morning.
Diesels also pre-heat before they crank. Ford's 6.7L Power Stroke uses glow plugs, one per cylinder. Ram's 6.7L Cummins has used an intake air heater, and Cummins says its redesigned 2025 engine adds glow plugs. Both run on battery power, so letting the heat cycle finish before cranking matters most when the batteries are already weak.
Step 1: Match the voltage, and know that two batteries doesn't mean 24 volts
This is the one choice that can cause damage if you get it wrong. A diesel pickup's two batteries share a 12-volt system. Ram's diesel manual is explicit: do not use a booster source greater than 12 volts, and a starting unit above 12 volts DC can damage the battery, starter, alternator or electrical system. Ford's 6.7L Super Duty supplement says to use only a 12-volt supply.
24-volt jump starters exist for equipment with 24-volt electrical systems. Some packs offer both outputs on a switch, which is useful for mixed fleets but adds a way to make a mistake, so confirm the setting before you connect. Size alone doesn't tell you the voltage: Freightliner's Business Class M2 manual, for example, describes a 12-volt battery system. Check the vehicle's manual or battery labels rather than assuming.
Step 2: Read the ratings that mean something
Peak amps are the headline number on most boxes and the least useful for comparison. Clore Automotive, which makes the Jump-N-Carry line, says peak amps have no industry-agreed definition, so two brands' figures may not be measured the same way.
Battery ratings work differently. Cold cranking amps (CCA) describe the current a new, fully charged battery delivers for 30 seconds at 0°F while holding at least 7.2 volts. Cranking amps (CA) use the same idea at 32°F, so CA and CCA aren't interchangeable. Some jump packs publish cranking or cold cranking figures; when they do, check the test conditions are stated.
The most practical figure is usually the maker's own application rating, such as NOCO's statement that its GB150 is designed for diesel engines up to 7.0 liters. Treat it as the maker's claim for a healthy setup, then leave margin for cold, a deeply discharged battery bank and a high-mileage starter. A UL 2743 listing tells you the pack was evaluated for safety, which is worth having on a lithium pack you'll leave in a cab, but it isn't a measure of starting power.
| Rating | What it measures | Useful for comparing diesel packs? |
|---|---|---|
| Peak amps | Not defined by any industry-agreed standard | No; methods differ between brands |
| Cold cranking amps (CCA) | 30-second output at 0°F while holding 7.2V (battery rating) | Yes, when the test conditions are published |
| Cranking amps (CA) | 30-second output at 32°F (battery rating) | Only against other CA figures |
| Maker's diesel engine-size rating | The maker's claim for the largest diesel it is designed to start | Yes, as a starting point with margin |
| UL 2743 | Portable power pack safety evaluation | For safety, not starting power |
Step 3: Check the temperature limits
Lithium jump packs publish two temperature ranges, and the difference matters if the pack lives in the truck. NOCO's GB150 data sheet lists operation from −4°F to 122°F but charging only from 32°F to 104°F. A pack left in a cab overnight in a northern winter may work below freezing yet should be brought inside to recharge.
Before you connect anything in very cold weather, look at the truck's batteries. NOCO's manual says not to jump-start a frozen battery; signs include a bulging or cracked case. Get a frozen battery replaced or professionally checked rather than forcing current into it.
Step 4: Respect the cranking and rest limits
Diesels often take longer to catch, which tempts people to keep cranking. Every pack has a duty cycle, and they differ. Clore's JNC770 manual says that if the vehicle doesn't start within 6 seconds, let the unit cool for 3 minutes before trying again. NOCO's GB150 guide says to wait 20 to 30 seconds between attempts, make no more than five attempts in 15 minutes, then let the pack rest for 15 minutes.
Long cranking also heats the truck's starter. If a diesel won't start after a few properly spaced attempts with the heater cycle completed, the problem is unlikely to be solved by more cranking. Check fuel, the batteries' condition and connections, and the codes stored by the engine computer.
Step 5: Connect the way your truck's manual says
Clamp locations differ by truck and model year, so the owner's manual is the authority. The 2019 Ram heavy-duty diesel manual, for example, says to put the transmission in PARK, apply the parking brake and turn off lights, heater and other loads; connect positive to the designated jump post rather than the fuses; and connect negative to a good engine-block ground, not to the discharged battery's negative post. Afterward, remove the engine-ground connection first.
Ford's 2016 6.7L supplement adds a warning that matters on any truck with modern electronics: don't disconnect the disabled truck's battery, because that can damage the electrical system. Then let the glow plugs or intake heater finish: Ford says to wait until the glow-plug light goes off before starting.
- Confirm 12-volt output before connecting.
- Vehicle in PARK, parking brake on, electrical loads off.
- Positive to the manual's designated point; negative to the specified ground.
- Wait for the glow-plug or Wait To Start light to go out.
- Crank within the pack's time limit, then rest as its manual specifies.
What this guide doesn't cover
- Exact clamp points for your truck: these vary by make, model year and battery layout, so use your owner's manual.
- Class 8 tractors and equipment that may use 24-volt systems; confirm the voltage on the vehicle.
- A minimum peak-amp or CCA figure for every diesel pickup. No standard figure was verified, so this guide doesn't give one.
- Product rankings. For researched and hands-on picks, see the related buying guides below.
Frequently asked questions
What size jump starter do I need for a diesel truck?
Start with voltage: diesel pickups use 12-volt systems. Then use the pack maker's diesel engine-size rating rather than peak amps, and leave margin for cold weather and very flat batteries. For example, NOCO rates its GB150 for diesel engines up to 7.0 liters.
My truck has two batteries. Do I need a 24V jump starter?
No, not for a pickup with a 12-volt system. Ram's diesel manual says its two batteries are 12-volt and prohibits any 24-volt booster source, because excess voltage can damage the battery, starter, alternator or electrical system.
Are peak amps a good way to compare jump starters?
No. Clore Automotive says peak amps have no industry-agreed definition, so figures from different brands may not be comparable. A maker's engine-size rating, or cranking figures with stated test conditions, is more useful.
Which battery do I connect to on a diesel truck with two batteries?
Use the connection points in your truck's owner's manual. The 2019 Ram heavy-duty diesel manual, for example, specifies a jump post for positive and an engine-block ground for negative, not the battery's negative post.
Should I wait for the glow plug light before cranking with a jump pack?
Yes. Ford says to wait until the glow-plug light goes off before starting its 6.7L diesel, and Ram's remote start waits for the Wait To Start light. Pre-heating first gives the engine its best chance on the first attempt.
Can a lithium jump starter work in freezing weather?
Many can, within their published limits. NOCO's GB150 lists operation down to −4°F but charging only from 32°F, so store it within its range and recharge it indoors. Never jump-start a frozen battery.
Sources
- 2019 Ram 2500/3500/4500/5500 Diesel Supplement (FCA US (Mopar)) — used for: Two 12V batteries, 24V prohibition, damage warning, connection points, intake heater and Wait To Start
- 2016 Ford 6.7L Diesel F-250–F-550 Supplement (Ford Motor Company) — used for: 12V-only supply, battery-disconnect warning, eight glow plugs, wait for the indicator
- Cummins Launches Next Generation 6.7L Turbo Diesel Pickup Engine System for 2025 Ram Heavy Duty Trucks (Cummins Inc.) — used for: Glow plugs on the 2025 6.7L
- How Temperature Affects a Battery (Interstate Batteries) — used for: Battery strength loss at 32°F and 0°F
- Cranked Up: How Battery Cranking Amps Are Calculated and Used (quoting OPTIMA Batteries) (Dragzine) — used for: Why diesels need more cranking energy; CA test temperature
- Cold Cranking Amps (OPTIMA Batteries) — used for: CCA test conditions
- Peak Amps – Don't Tell the Whole Story (Clore Automotive) — used for: Peak amps have no agreed definition
- Portable Power Pack Testing (UL 2743) (UL Solutions) — used for: Scope of the UL 2743 safety standard
- BOOST PRO GB150 Data Sheet (NOCO) — used for: Diesel engine-size rating; operating and charging temperatures
- GB150 User Guide (NOCO) — used for: Attempt and rest limits; frozen-battery warning
- Jump-N-Carry JNC770 Operator's Manual (Clore Automotive) — used for: 6-second cranking limit and 3-minute cool-down
- Business Class M2 Driver's Manual (Daimler Truck North America) — used for: Example of a 12V system on a commercial truck
Cite this guide
You're welcome to quote the short answer or any key fact, with a link to this page. Each fact has its own anchor link so you can point readers to the exact line.
Holden, R. (2026). How to Choose a Jump Starter for a Diesel Truck. RateThisPro Automotive Research Library. https://ratethispro.com/research-library/how-to-choose-a-jump-starter-for-a-diesel-truck
Related RateThisPro guides
- Best heavy-duty jump starters for big trucks
- Jump starters for semi trucks
- How to jump a car battery safely
- Ram 1500 & 2500 Cummins diagnostic guide
- Ford F-150 & Super Duty diagnostic guide