P0174 Code: System Too Lean (Bank 2)
By Roger Holden. Updated November 10, 2026. Researched guidance from manufacturer bulletins and OBD II rules, not a vehicle diagnosis.
Standard definition: System Too Lean (Bank 2). System: Fuel system monitor. Severity: Moderate.
Sources for this section: [3] SAE J2012; [4] GM 22-NA-171; [6] Nissan NTB19-022; [7] Lexus L-SB-0005-23
P0174 means the engine computer detected a lean fuel-system condition on bank 2. It is not an instruction to replace an oxygen sensor. Manufacturer bulletins connect this code with intake leaks, crankcase-ventilation connections, calibration problems and loss of fuel pressure, so the diagnostic evidence matters more than the part named in an online repair suggestion.
The bank designation identifies which monitored engine bank reported the condition. Do not select a repair side from a generic left-versus-right diagram: use the engine's service information to identify bank 2 and its sensors. Also check whether P0171 is present, because that is the corresponding bank 1 lean code.
The examples below are documented leads, not a ranking of failure rates. GM describes cracked intake boots and software-related complaints on specified Colorado and Canyon applications. Lexus documents fuel-pressure loss on listed models, while Nissan publishes an air-fuel sensor confirmation procedure intended to prevent unsupported sensor replacement.
Moderate: diagnose soon and respond to running problems
EPA advises arranging attention soon for a steady check engine light. P0174 does not tell you how much fuel pressure remains, whether the car will restart or whether another fault is present. Documented complaints range from an illuminated warning to hard starting with pressure loss. A flashing light changes the situation because EPA associates it with severe problems such as a catalyst-damaging misfire.
Stop where safe and get help if:
- The check engine light flashes, especially with shaking or obvious misfiring.
- The engine stalls or loses enough power that continued driving is unsafe.
- You smell strong raw fuel or see liquid fuel leaking; do not restart until the hazard is assessed.
How the computer sets P0174
California 13 CCR 1968.2, section (e)(6.1), requires the fuel delivery system to be monitored for its ability to maintain emissions compliance. Section (e)(6.2.2) also requires a malfunction to be detected when adaptive feedback control has used all the adjustment allowed by the manufacturer, subject to the regulation's stated exception for secondary-sensor feedback.
Fuel-trim data are useful evidence of that adjustment. Lexus L-SB-0005-23 describes positive trims with fuel-pressure loss, including a no-pressure condition verified using a manual gauge. Positive correction is therefore a reason to investigate what the controller is compensating for, not proof that the sensor reporting the condition has failed.
Section (e)(6.3.1) requires continuous monitoring for the specified fuel-delivery and adaptive-feedback faults, subject to its exception. That does not establish one universal percentage, engine speed or elapsed time for setting P0174. The manufacturer defines the applicable diagnostic criteria; this guide does not assign a generic fuel-trim cutoff.
A calibration issue can also be involved. GM 21-NA-105 describes software anomalies on its specified applications and calls for an inspection followed by the current ECM software. A software-related bulletin is a reason to verify applicability early, not a reason to skip inspection or assume that every lean code is false.
Sources for this section: [1] California Code of Regulations, Title 13 §1968.2
Common symptoms
- A steady check engine light with P0174 stored, as described in the manufacturer bulletins.
- P0171 stored alongside P0174; GM documents both codes occurring together on specified applications.
- Hard starting on the Lexus applications covered by its fuel-pressure-loss bulletin.
- Positive fuel trims or low fuel pressure found during diagnosis, rather than an obvious symptom the driver can identify.
- A flashing light or pronounced shaking requires separate prompt attention for a possible severe misfire.
Possible causes of P0174
- Intake boot or duct leakage: GM 22-NA-171 identifies a cracked or failed rubber intake boot on specified 2017–2022 Colorado and Canyon vehicles with the 3.6L LGZ engine. It directs inspection for cracking or weld failure and says not to remove the engine cover during the leak check.
- PCV or crankcase connections not sealed: GM 21-NA-105 calls for inspecting PCV hoses and oil-separator connections, the oil filler cap, the filler adapter and dipstick seating. These are worthwhile inspection points on applicable vehicles before replacing a sensor or authorizing a fuel-system repair.
- Vehicle-specific ECM calibration: The same GM bulletin describes possible software anomalies on specified 2020–2021 Colorado and Canyon applications. After its visual checks, it calls for checking and updating ECM software, running the vehicle and continuing normal diagnosis if codes return. Applicability and current calibration must be confirmed.
- Insufficient fuel pressure: Lexus L-SB-0005-23 links P0171 or P0174 and hard starting with fuel-pressure loss on its listed applications. It describes positive fuel trims and pressure verification using a manual gauge. This supports measuring pressure before condemning a pump, not replacing one from a code alone.
- Air-fuel sensor fault established by testing: Nissan NTB19-022 requires its specified air-fuel sensor confirmation procedure on applicable vehicles. Its flow chart permits replacement when the relevant confirmation codes are detected; otherwise it explicitly says not to replace the sensor and to continue lean-code diagnosis excluding it.
Sources for this section: [4] GM 22-NA-171; [5] GM 21-NA-105; [7] Lexus L-SB-0005-23
How to diagnose P0174, step by step
- Record stored and pending codes, available freeze-frame data and live fuel trims before clearing anything. Save engine temperature, speed and load where available. Capture the original complaint and starting behavior. This preserves the evidence before a later procedure resets learned values or changes the operating conditions.
- Review related codes, especially P0171, misfire codes and fuel-pressure or sensor faults. Note which banks are affected instead of assuming that P0174 proves a bank-specific mechanical leak. The cited bulletins describe both shared-system complaints and sensor-testing branches; the code combination helps select the right procedure.
- Check current manufacturer service information and bulletins by exact vehicle, engine and production applicability. Identify any calibration instructions early. On an applicable GM 21-NA-105 vehicle, perform its visual checks before the prescribed update rather than treating the bulletin as permission to flash the ECM without inspection.
- Inspect the intake path and crankcase-related connections using the applicable procedure. GM's checklist includes PCV and separator connections, filler components and dipstick seating. For a vehicle covered by 22-NA-171, inspect the boot for cracking or weld failure and observe its instruction about leaving the engine cover installed during leak checking.
- Follow any manufacturer-directed sensor confirmation branch. Nissan NTB19-022 is an important example: its flow chart tests air-fuel sensor function before deciding whether replacement is justified. Save the original data first, then follow its required learning resets and test conditions only on the applications it covers.
- If inspection and applicable software or sensor checks do not establish the cause, continue the manufacturer's lean-code diagnosis. Test fuel pressure against the vehicle's specification rather than interpreting a trim reading as a pump diagnosis. Lexus's bulletin illustrates the importance of confirming an actual pressure problem with appropriate equipment.
- Repair the verified defect and perform the specified confirmation test. Recheck codes and fuel-system data under the relevant conditions. GM directs technicians to run the vehicle after its correction and continue service-information diagnosis if the codes reset. Erasing P0174 without that follow-up does not demonstrate a successful repair.
Record stored, pending and permanent codes and available freeze-frame data before clearing anything. Clearing codes does not fix the fault; it can erase useful evidence and reset emissions readiness monitors.
Sources for this section: [5] GM 21-NA-105; [6] Nissan NTB19-022
Mistakes that cost money
- Replacing the bank 2 air-fuel sensor from P0174 alone. Nissan's applicable procedure specifically says not to replace it when its confirmation test does not support that repair.
- Skipping simple intake and PCV connection checks. GM documents both failed intake boots and improperly sealed crankcase-related connections.
- Using one universal fuel-trim percentage as a diagnosis. CARB refers to manufacturer-allowed adjustment, not a universal P0174 cutoff.
- Replacing a fuel pump or updating software solely because a bulletin mentions it. Verify the vehicle, test result and correction criteria first.
Codes often seen with it
- P0171 — Lean fuel-system condition on bank 1; record whether both banks are affected.
- P0300 — Random/multiple-cylinder misfire; investigate promptly, especially with a flashing light.
- P0087 — Fuel rail/system pressure too low; listed alongside lean codes in the Lexus fuel-pressure bulletin.
Scanner features that help with P0174
- Stored and pending codes with freeze-frame capture
- Live short- and long-term fuel trims for both banks
- Air-fuel or oxygen-sensor live data supported by the vehicle
- Fuel-pressure data where available, without treating it as a substitute for prescribed gauge tests
- Manufacturer-specific confirmation tests and calibration identification
Compare OBD2 scanners for home mechanics or bidirectional scan tools.
Frequently asked questions
Does P0174 mean the bank 2 oxygen sensor is bad?
No. Nissan publishes a specific confirmation procedure and warns against replacement when that test does not support it. Intake leaks, connection problems, calibration issues and fuel-pressure loss are documented alternatives on particular vehicles.
What does bank 2 tell me?
It identifies the engine bank associated with the lean-system result, not the failed component. Use the engine's service diagram to locate that bank and its sensors; do not assume a universal driver-side or passenger-side location.
Why are P0171 and P0174 both present?
Both monitored banks have reported lean-system faults. GM documents both codes with specified intake and calibration complaints, while Lexus lists them with pressure loss. The pair does not prove that two sensors failed.
Can software cause P0174?
On particular vehicles, yes. GM 21-NA-105 describes possible software anomalies and requires visual checks followed by current ECM software on its applicable vehicles. Other models still need their own diagnostic procedure; this is not a universal reprogramming recommendation.
Can I drive with P0174?
A steady light calls for service soon, but the code alone cannot establish safety. Stop for a flashing light, significant shaking, stalling, unsafe power loss or a fuel leak. Hard starting and pressure loss deserve prompt diagnosis rather than repeated code clearing.
Sources
- [1] California Code of Regulations, Title 13 §1968.2 — OBD II malfunction and diagnostic system requirements — used for: How each monitor is required to detect the fault, and when the check engine light turns on and off
- [2] US EPA — Do you drive a 1996 or newer car or light truck? (EPA-420-F-02-016) — used for: What a steady or blinking check engine light means for drivers
- [3] SAE J2012 — Diagnostic Trouble Code Definitions — used for: The standard that defines generic code numbers and descriptions
- [4] GM 22-NA-171 — P0171/P0174 and failed intake boot (via NHTSA) — used for: Manufacturer wording "P0174: Fuel Trim System Lean Bank 2"; cracked or failed intake boot on specified 2017–2022 Colorado/Canyon LGZ applications and inspection instructions
- [5] GM 21-NA-105 — ECM calibration for P0171/P0174 (via NHTSA) — used for: Possible software anomalies on specified Colorado/Canyon applications; PCV, oil-separator, filler and dipstick checks before current ECM software and subsequent verification
- [6] Nissan NTB19-022 — P0171 and P0174 service information (via NHTSA) — used for: Manufacturer wording "P0174 (FUEL SYS LEAN B2)"; air-fuel sensor confirmation procedure and explicit instruction not to replace the sensor when the specified confirmation does not support replacement
- [7] Lexus L-SB-0005-23 — Fuel pump loss of fuel pressure (via NHTSA) — used for: Manufacturer wording "DTC P0171 and/or P0174 (System Too Lean Bank 1/Bank 2)"; hard starting, positive fuel trims, P0087 and pressure verification with a manual gauge on listed applications
Other code guides
- P0420: Catalyst System Efficiency Below Threshold (Bank 1)
- P0300: Random/Multiple Cylinder Misfire Detected
- P0171: System Too Lean (Bank 1)
- P0455: Evaporative Emission System Leak Detected (Large Leak)
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
- P0442: Evaporative Emission System Leak Detected (Small Leak)
- P0456: Evaporative Emission System Leak Detected (Very Small Leak)
- P0301: Cylinder 1 Misfire Detected
- P0430: Catalyst System Efficiency Below Threshold (Bank 2)