P0300 Code: Random/Multiple Cylinder Misfire Detected
By Roger Holden. Updated November 10, 2026. Researched guidance from manufacturer bulletins and OBD II rules, not a vehicle diagnosis.
Standard definition: Random/Multiple Cylinder Misfire Detected. System: Misfire monitor. Severity: High.
Sources for this section: [3] SAE J2012; [4] Volkswagen 01-16-13; [5] Kia TSB
P0300 means the engine computer counted misfires but couldn't blame a single cylinder, either because several cylinders are misfiring or because the pattern moves around. A misfire is a combustion event that didn't happen properly, so unburned fuel goes into the exhaust.
This is the code on this list where timing matters most. Unburned fuel heats the catalytic converter, and a severe misfire can damage it quickly. If the check engine light is flashing, treat that as the headline and the code as the detail.
High: a flashing light needs prompt attention
Misfires can overheat and damage the catalytic converter and may come with loss of power. The EPA advises minimizing time on the road and avoiding high speed and heavy loads such as towing when the light blinks. That isn't a promise that driving is safe: if the engine shakes or loses power, stop where safe and get help.
Stop where safe and get help if:
- The check engine light is flashing
- The engine shakes badly, stalls or loses significant power
- You smell fuel or see smoke
- The temperature or oil warning comes on as well
How the computer sets P0300
Under California's OBD II rules, the misfire monitor watches for misfire continuously and must identify the specific cylinder where it can. That's why you will often see P0300 alongside P0301 to P0308, which name cylinders one to eight. Manufacturers calculate the misfire rate that would overheat the converter for each speed and load, and the computer checks against it in 200-revolution blocks.
When that catalyst-damaging rate is exceeded, the rules require the check engine light to blink once per second while the misfire is happening. A lower, emissions-level misfire rate produces a steady light instead. The EPA's driver guidance describes a blinking light as a severe engine problem, such as a catalyst-damaging misfire, that should be addressed as soon as possible.
Sources for this section: [1] California Code of Regulations, Title 13 §1968.2
Common symptoms
- Flashing or steady check engine light
- Rough idle, shaking or a stumble under acceleration
- Loss of power or hesitation, especially climbing or towing
- Fuel smell from the exhaust or poorer fuel economy
Possible causes of P0300
- Ignition wear: Worn spark plugs, failing ignition coils, damaged plug wires or boots. Moisture or oil in plug wells can cause misfires that wander between cylinders.
- Lean running or vacuum leaks: Unmetered air or low fuel delivery affects every cylinder, so misfires can appear random. Check for P0171 or P0174 alongside.
- Fuel delivery and injectors: Low fuel pressure, a weak pump, a restricted filter, or clogged or leaking injectors.
- Mechanical problems: Low compression from valve, piston-ring, head-gasket or timing problems. These are less common but expensive, which is why testing comes before parts.
- Fuel quality: Contaminated fuel or the wrong fuel can cause widespread misfiring.
- Manufacturer-specific issues: Some engines have published bulletins. Volkswagen's misfire diagnostic aid covers P0300 and P0301–P0308 on many gasoline engines and warns against replacing multiple components for one misfiring cylinder.
Sources for this section: [5] Kia TSB; [6] Edmunds
How to diagnose P0300, step by step
- If the light is flashing or the engine is shaking, reduce load and stop where safe before doing any diagnosis.
- Record all codes and freeze-frame data: engine speed, load, coolant temperature and fuel trims when the misfire set. Note whether it happens cold, at idle, under load or in wet weather.
- Look for cylinder-specific codes (P0301–P0308) and fuel-trim codes. A lean code points toward air or fuel delivery; a single cylinder points toward that cylinder's coil, plug or injector.
- Check live misfire counters per cylinder, or Mode 6 misfire data, if your scanner supports it.
- With the engine off and cool, inspect plugs, coils and wiring. On engines with coil-on-plug, a technician may swap coils between cylinders to see whether the misfire follows the part.
- If ignition looks healthy, test fuel pressure and injector operation, then compression or leak-down for mechanical causes. Check for bulletins on your exact engine before replacing parts.
Record stored, pending and permanent codes and available freeze-frame data before clearing anything. Clearing codes does not fix the fault; it can erase useful evidence and reset emissions readiness monitors.
Sources for this section: [4] Volkswagen 01-16-13
Mistakes that cost money
- Replacing every spark plug, coil and injector at once: Volkswagen's guidance specifically says multiple components shouldn't be replaced for one misfiring cylinder.
- Clearing the code and driving on: the light may stay off briefly while the converter keeps taking damage.
- Ignoring a companion lean code, which can be the real cause of the random misfire.
- Replacing the catalytic converter for P0420 before the misfire that damaged it is fixed.
Codes often seen with it
- P0301–P0308 — Misfire on a specific cylinder
- P0171 — Lean mixture that can cause random misfires
- P0420 — Converter efficiency fault that often follows misfires
Scanner features that help with P0300
- Freeze-frame data
- Per-cylinder misfire counters or Mode 6 data
- Live fuel-trim data
- Readiness monitor status
Compare OBD2 scanners for home mechanics or bidirectional scan tools.
Frequently asked questions
Is P0300 serious?
It can be. If the check engine light is flashing, the misfire is severe enough to damage the catalytic converter. Reduce load, avoid towing and high speed, and get prompt help; stop safely if the engine shakes or loses power.
What is the most common cause of P0300?
Repair references most often find ignition wear, such as spark plugs and coils, or a lean condition from vacuum leaks or weak fuel delivery. Your freeze-frame and companion codes decide which, not averages.
Can bad gas cause a P0300 code?
Yes, contaminated or incorrect fuel can cause widespread misfires. It's one possibility to rule in or out after checking ignition and fuel-trim data.
What's the difference between P0300 and P0301?
P0301 names cylinder 1. P0300 means the misfire is random, on more than one cylinder, or couldn't be assigned to a single cylinder.
Will clearing P0300 fix it?
No. Clearing erases freeze-frame evidence and resets readiness monitors. If the misfire returns, the code will come back.
Sources
- [1] California Code of Regulations, Title 13 §1968.2 — OBD II malfunction and diagnostic system requirements — used for: How each monitor is required to detect the fault, and when the check engine light turns on and off
- [2] US EPA — Do you drive a 1996 or newer car or light truck? (EPA-420-F-02-016) — used for: What a steady or blinking check engine light means for drivers
- [3] SAE J2012 — Diagnostic Trouble Code Definitions — used for: The standard that defines generic code numbers and descriptions
- [4] Volkswagen 01-16-13 — Engine Misfire Diagnostic Aid (via NHTSA) — used for: Code wording "Random/Multiple Cylinder Misfire Detected" and the warning against replacing multiple components
- [5] Kia TSB — P0420 with or without P030X misfire codes (via NHTSA) — used for: Code wording and the link between misfire and catalyst efficiency faults
- [6] Edmunds — P0300: Random/Multiple Cylinder Misfire Detected — used for: Common symptoms and causes
Other code guides
- P0420: Catalyst System Efficiency Below Threshold (Bank 1)
- P0171: System Too Lean (Bank 1)
- P0455: Evaporative Emission System Leak Detected (Large Leak)
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
- P0442: Evaporative Emission System Leak Detected (Small Leak)
- P0456: Evaporative Emission System Leak Detected (Very Small Leak)
- P0174: System Too Lean (Bank 2)
- P0301: Cylinder 1 Misfire Detected
- P0430: Catalyst System Efficiency Below Threshold (Bank 2)