P0301 Code: Cylinder 1 Misfire Detected
By Roger Holden. Updated November 10, 2026. Researched guidance from manufacturer bulletins and OBD II rules, not a vehicle diagnosis.
Standard definition: Cylinder 1 Misfire Detected. System: Misfire monitor. Severity: High.
Sources for this section: [3] SAE J2012; [5] FCA TSB 08-053-25
P0301 means the engine computer identified a misfire on cylinder 1. It identifies where combustion went wrong, not which part failed. A spark plug, coil or injector can be involved, but a cylinder that cannot maintain compression can produce the same code. Replacing an ignition coil without testing is still a guess.
The useful difference from P0300 is the starting point: you have one named cylinder to compare with the others. Volkswagen’s diagnostic aid calls for moving components between cylinders before replacing them, then testing injector leakage and compression if the misfire stays put. Its warning is clear: do not replace multiple components for one misfiring cylinder. This guide explains that approach; the repair manual for your engine still controls access, specifications and safe testing.
High: a flashing light changes the plan
A cylinder-specific code is not a minor version of a random misfire. EPA guidance describes a blinking light as a severe problem such as catalyst-damaging misfire, and advises minimizing road time and avoiding high speed and heavy loads. Do not road-test a badly running engine just to make a swap result appear. Stop safely and arrange help when operation is unstable; the code alone cannot certify that driving is safe.
Stop where safe and get help if:
- The check engine light is flashing: stop the diagnostic drive and seek prompt help.
- The engine runs so roughly or loses enough power that you cannot drive safely.
- A temperature or oil-pressure warning appears; do not continue a misfire test with another urgent warning.
How the computer sets P0301
California 13 CCR 1968.2, section (e)(3), requires monitoring for engine misfire and identification of the affected cylinder, with approved exceptions where reliable cylinder identification is not possible. P0301 is the cylinder 1 result. It is not a direct electrical test of the coil or injector, so neither component is convicted by the code alone.
For catalyst-damaging misfire, the regulation describes evaluating the manufacturer’s misfire percentage in 200-revolution increments at each engine speed and load, with specified exceptions. It requires a once-per-second blinking malfunction light while the qualifying misfire is occurring, subject to the regulation’s alternative strategies. Emissions-level misfire has separate criteria. Do not infer a universal misfire count or compression specification from these rules; those depend on the vehicle and test.
Sources for this section: [1] California Code of Regulations, Title 13 §1968.2
Common symptoms
- A steady or flashing check engine light; Volkswagen lists both with cylinder-specific misfire codes.
- Hesitation or misfiring while the engine is running, as described in FCA’s affected-vehicle bulletin.
- Rough running confined to a cold start or other particular condition; Subaru documents a cylinder 1 example that improved after warm-up.
- Reduced performance, which Volkswagen notes can accompany misfire faults without a large loss of power.
Possible causes of P0301
- Connections and previously disturbed parts: Check cylinder 1 electrical connections and relevant grounds before buying parts. Volkswagen names loose or damaged connections and circuit grounds among misfire-related conditions. Review recent service history as well: the diagnostic aid specifically asks technicians to check previous maintenance and misfire repairs.
- Cylinder 1 spark plug or ignition coil: A component-specific ignition fault is worth isolating early. Volkswagen recommends swapping plugs and coils between cylinders and checking whether the misfire migrates. Move and document parts separately so the result identifies one component rather than a group. This applies where the engine layout allows those swaps.
- Cylinder 1 injector malfunction: Volkswagen includes practical injector swaps and an internal leakage test when ignition swaps do not move the fault. Honda also documents injector wear or clogging with misfire codes on specific vehicles. That is evidence for testing the injector, not permission to replace an entire set on every engine.
- Compression or cylinder-specific airflow trouble: If component swaps and injector checks do not explain the misfire, Volkswagen directs compression testing. Subaru’s cold-start P0301 case included normal compression and leak-down results; a malformed intake diverter restricted cylinder 1 airflow. Mechanical testing and condition-specific intake checks can therefore matter even when ignition parts look serviceable.
- Shared fuel conditions or applicable software: One cylinder code does not rule out a wider problem. Volkswagen discusses poor fuel quality, low-fuel companion faults and software review. FCA specifies an ignition-control software update for certain 2023 Wagoneer/Grand Wagoneer vehicles. Verify exact applicability rather than treating a bulletin as a general repair instruction.
Sources for this section: [4] Volkswagen 01-16-13, 2033805/8; [5] FCA TSB 08-053-25; [6] Subaru October 2020 TechTIPS
How to diagnose P0301, step by step
- Record evidence first, once the vehicle is safely stopped. Save stored and pending codes, available permanent codes and freeze-frame data before clearing anything. Note engine speed, load, coolant temperature and whether the problem occurred cold, warm or during acceleration. Volkswagen starts with the fault memory and environmental conditions because an intermittent misfire may disappear before the appointment.
- Address related faults next. Volkswagen directs technicians to investigate other entries before cylinder misfires; its low-fuel example shows why context matters. If other cylinders also have codes, do not assume cylinder 1 has an isolated coil failure. Keep the original scan report so later testing can distinguish an existing problem from a code introduced during diagnosis.
- Check applicable bulletins, campaigns and software before component replacement. Match engine, model year and any VIN limits, then review previous work. Volkswagen places this review early in its procedure. FCA’s software bulletin is an example, not a recommendation to reflash every vehicle with P0301. Use the manufacturer’s current test plan for the actual vehicle.
- Identify cylinder 1 from vehicle-specific service information before touching components; do not choose the easiest cylinder to reach. With the engine off and safe to work on, inspect its connections and accessible ignition components. Reproduce the original condition only when safe, and use supported cylinder-misfire data to confirm which cylinder is active rather than relying on feel alone.
- Perform a controlled ignition swap where the repair manual permits it. Label the original cylinder locations. Move cylinder 1’s coil to a known comparison cylinder and retest; evaluate the plug separately so the two tests remain distinguishable. If the misfire moves with one part, Volkswagen’s procedure supports replacing that proven part. If it stays on cylinder 1, do not keep buying coils.
- Test the injector and mechanical condition if the fault stays. Volkswagen specifies injector internal-leakage testing when injectors have not been swapped, followed by compression testing if that does not explain the fault. Leave injector removal and fuel-system work to a qualified technician. Compression and, when indicated, leak-down testing should follow engine-specific procedures, not a universal internet pressure or percentage limit.
- Verify the repair under the original operating conditions and re-read fault memory. Volkswagen explicitly calls for the same environmental conditions used in the original fault log. For a cold-start complaint, a warm idle alone is not the equivalent check. Confirm supported misfire data no longer shows the original problem and complete the manufacturer’s readiness procedure without deliberately continuing a severe misfire.
Record stored, pending and permanent codes and available freeze-frame data before clearing anything. Clearing codes does not fix the fault; it can erase useful evidence and reset emissions readiness monitors.
Sources for this section: [4] Volkswagen 01-16-13, 2033805/8; [5] FCA TSB 08-053-25; [6] Subaru October 2020 TechTIPS
Mistakes that cost money
- Replacing the plug, coil and injector together. That destroys the comparison Volkswagen asks for and may replace working components.
- Swapping parts without labeling their destinations or saving the new scan results. A migration test needs a documented before-and-after cylinder assignment.
- Calling an unmoved misfire a bad engine before checking the injector. Volkswagen puts injector leakage testing ahead of compression testing when the injector has not been swapped.
- Accepting a warm-engine test for a cold-start complaint. Subaru’s documented P0301 case required attention to the warm-up condition to find the airflow restriction.
Codes often seen with it
- P0300 — Random/multiple-cylinder misfire; compare the overall pattern before treating cylinder 1 in isolation.
- P0302 — Cylinder 2 misfire; after a documented swap, a new cylinder-specific result can help identify a migrated component.
- P0420 — Bank 1 catalyst-efficiency fault; address an active misfire before judging the catalyst.
- P0430 — Bank 2 catalyst-efficiency fault; companion engine-running faults need investigation first.
Scanner features that help with P0301
- Saved freeze-frame and full fault reports, including pending codes, for before-and-after comparison.
- Per-cylinder misfire counters through manufacturer-enhanced data, or Mode 6 where the vehicle and tool actually expose identifiable cylinder results.
- Live engine speed, load and coolant temperature to match the original fault conditions.
- Manufacturer-guided tests or injector tests where supported; a basic code reader is not equivalent to the factory diagnostic system.
Compare OBD2 scanners for home mechanics or bidirectional scan tools.
Frequently asked questions
Does P0301 mean the cylinder 1 coil is bad?
No. It means cylinder 1 misfired. A coil is one candidate; Volkswagen requires evidence that a misfire follows a component before blaming it. A fault that stays can require injector and compression testing.
What does it mean if the misfire follows the coil?
If a controlled test moves the misfire to the cylinder receiving that coil, the coil is implicated. Document the new result and replace the proven faulty part, then verify the repair. Do not move the plug with it and assume you have isolated the coil.
What if a new plug and coil do not fix P0301?
Stop replacing ignition parts. Check the original test conditions, injector operation and leakage, then compression as the manufacturer directs. Subaru’s published example also shows that a cylinder-specific intake restriction can survive normal mechanical test results.
Can I drive with P0301 if the light is steady?
A steady light does not establish that driving is safe. Arrange diagnosis promptly. If the light flashes or the vehicle cannot be controlled normally because of rough running or power loss, stop safely and get assistance rather than continuing a test drive.
Will clearing P0301 prove the repair worked?
No. Volkswagen calls for verification under the original conditions. Save evidence before clearing, complete the appropriate retest and check for returning faults. An intermittent cold-start misfire has not been disproved simply because the engine runs well when warm.
Sources
- [1] California Code of Regulations, Title 13 §1968.2 — OBD II malfunction and diagnostic system requirements — used for: How each monitor is required to detect the fault, and when the check engine light turns on and off
- [2] US EPA — Do you drive a 1996 or newer car or light truck? (EPA-420-F-02-016) — used for: What a steady or blinking check engine light means for drivers
- [3] SAE J2012 — Diagnostic Trouble Code Definitions — used for: The standard that defines generic code numbers and descriptions
- [4] Volkswagen 01-16-13, 2033805/8 — Engine, Misfire Diagnostic Aid (via NHTSA) — used for: Wording "Cyl.1 Misfire Detected"; freeze-frame and related-code priority; TSB/software review; component migration tests; injector leakage and compression testing; verification under original conditions
- [5] FCA TSB 08-053-25 — Ignition System Control Module updates (via NHTSA) — used for: Exact wording "Cylinder 1 Misfire Detected" and "Catalyst System Efficiency Below Threshold Bank 2"; software repair for specified 2023 Wagoneer/Grand Wagoneer vehicles; other faults addressed first
- [6] Subaru October 2020 TechTIPS — QMR of the Month (via NHTSA) — used for: Documented P0301 cold-start case with compression and leak-down tests within specification; cylinder 1 intake diverter restriction ultimately identified; condition-specific testing rather than assumed ignition failure
Other code guides
- P0420: Catalyst System Efficiency Below Threshold (Bank 1)
- P0300: Random/Multiple Cylinder Misfire Detected
- P0171: System Too Lean (Bank 1)
- P0455: Evaporative Emission System Leak Detected (Large Leak)
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
- P0442: Evaporative Emission System Leak Detected (Small Leak)
- P0456: Evaporative Emission System Leak Detected (Very Small Leak)
- P0174: System Too Lean (Bank 2)
- P0430: Catalyst System Efficiency Below Threshold (Bank 2)