P0455 Code: Evaporative Emission System Leak Detected (Large Leak)
By Roger Holden. Updated November 10, 2026. Researched guidance from manufacturer bulletins and OBD II rules, not a vehicle diagnosis.
Standard definition: Evaporative Emission System Leak Detected (Large Leak). System: EVAP monitor. Severity: Low to moderate.
Sources for this section: [3] SAE J2012; [4] Kia TSB
P0455 means the evaporative emission (EVAP) system, which traps gasoline vapor from the tank and burns it in the engine, failed its leak test with what the computer treats as a large leak. Fuel vapor that should stay sealed is escaping somewhere between the tank and the engine.
It's one of the few codes where the first check costs nothing. The EPA's own guidance for drivers names a loose or missing gas cap as a cause of the check engine light. If the cap is fine, though, the leak still needs finding, and some vehicles have known valve faults.
Low to moderate: the cap check can't wait, the rest can be planned
A vapor leak rarely affects how the car drives, but it releases fuel vapor, will fail most emissions inspections and can hide a second fault behind the lit warning. Liquid fuel leaking is a different and dangerous situation.
Stop where safe and get help if:
- You smell strong raw fuel or see fuel dripping: don't drive or start the engine, keep ignition sources away and get professional help
- The check engine light is flashing
- The engine runs badly or stalls after refueling
How the computer sets P0455
California's OBD II rules require the computer to detect an EVAP leak at least as large as a 0.040-inch hole, and on many vehicles one as small as 0.020 inch, as well as a lack of purge flow. To test it, the computer seals the system with its valves and watches pressure or vacuum. If the system can't hold it, the leak code sets.
Manufacturers word the large-leak code slightly differently; Kia's bulletin lists "P0455 – Evaporative Emission System Leak Detected (Large Leak)" alongside P0456 for a small leak. The test only runs under specific conditions, such as a particular fuel level and a cold start, so the code can take days to return after a repair, or to confirm one.
Sources for this section: [1] California Code of Regulations, Title 13 §1968.2
Common symptoms
- Check engine light, usually with no change in how the car drives
- Fuel smell around the car, especially near the filler or tank
- A "check fuel cap" message on some vehicles
- Failed emissions inspection
Possible causes of P0455
- Fuel cap: Missing, loose, cross-threaded or with a worn seal. Check it first, and replace it with the correct part for the vehicle if it's damaged.
- Filler neck: Rust or damage where the cap seals can leak even with a good cap.
- Vent or canister close valve stuck open: Kia's bulletin for 2012–2017 Rio vehicles produced from June 21, 2011 through March 28, 2016 covers P0455 and P0456 caused by a stuck-open canister close valve; Hyundai published a similar inspection for certain Accents.
- Purge valve: A purge valve that doesn't seal can cause leak or flow codes.
- Hoses and the charcoal canister: Cracked, disconnected or chewed vapor hoses, or a damaged canister.
- Fuel tank pressure sensor or seals: A faulty sensor or leaking tank-top seals.
Sources for this section: [4] Kia TSB; [6] Hyundai TSB
How to diagnose P0455, step by step
- Check for a strong fuel smell or visible leak first. If there is one, don't drive; see the severity section.
- Inspect the fuel cap and filler neck. Tighten or replace the cap, then allow several drive cycles: the EPA advises having the vehicle serviced if the light stays on after a few short trips.
- Record codes and freeze-frame data. Look for other EVAP codes, such as P0440, P0442, P0446, P0449 or P0456, which narrow the search.
- Check for bulletins on your exact vehicle; several manufacturers have published EVAP valve fixes.
- If your scanner supports it, run the EVAP self-test or command the vent and purge valves. A technician will usually smoke-test the system at low pressure to see where vapor escapes.
- When a self-test finds nothing, manufacturer manual tests exist. Kia's procedure PS469, for example, requires the fuel tank to be at least half full or the test won't complete properly.
Record stored, pending and permanent codes and available freeze-frame data before clearing anything. Clearing codes does not fix the fault; it can erase useful evidence and reset emissions readiness monitors.
Sources for this section: [5] Kia PS469; [6] Hyundai TSB
Mistakes that cost money
- Buying an EVAP valve before checking the cap and filler neck.
- Smoke-testing a fuel system with improvised equipment or high pressure; EVAP testing uses low pressure and fuel-safe smoke.
- Clearing the code just before an inspection: the EVAP monitor is often the slowest to show ready again.
Codes often seen with it
- P0456 — EVAP very small leak (Kia calls it the small leak)
- P0442 — EVAP small leak on many vehicles
- P0440 — EVAP system malfunction
Scanner features that help with P0455
- Freeze-frame data
- EVAP leak self-test where supported
- Bidirectional control of purge and vent valves
- Readiness monitor status
Compare OBD2 scanners for home mechanics or bidirectional scan tools.
Frequently asked questions
Can a loose gas cap cause P0455?
Yes, and it's the first thing to check. The EPA advises making sure the cap isn't loose or missing; if the light doesn't go out after a few short trips, have the vehicle serviced.
Is P0455 dangerous?
A vapor leak usually isn't a driveability problem, but a strong raw-fuel smell or visible fuel leak is a fire risk. Don't drive in that case; keep ignition sources away and get help.
How long does it take for P0455 to clear after fixing it?
The EVAP test runs only under specific conditions, so it can take several days of normal driving. Under the California OBD II rules, the light turns off after three consecutive passing drive cycles.
What's the difference between P0455 and P0456?
Both come from the EVAP leak test. P0455 is the large-leak result; P0456 is the smallest leak the system checks for, described as a very small or small leak depending on the manufacturer.
Will an emissions test fail with P0455?
Most OBD-based inspection programs fail a vehicle with the check engine light commanded on, and an incomplete EVAP monitor can also cause a rejection.
Sources
- [1] California Code of Regulations, Title 13 §1968.2 — OBD II malfunction and diagnostic system requirements — used for: How each monitor is required to detect the fault, and when the check engine light turns on and off
- [2] US EPA — Do you drive a 1996 or newer car or light truck? (EPA-420-F-02-016) — used for: What a steady or blinking check engine light means for drivers
- [3] SAE J2012 — Diagnostic Trouble Code Definitions — used for: The standard that defines generic code numbers and descriptions
- [4] Kia TSB — P0455/P0456 caused by a stuck-open canister close valve, 2012–2017 Rio (via NHTSA) — used for: Code wording and a known valve cause
- [5] Kia PS469 — Manual EVAP test for hard-to-find leaks (via NHTSA) — used for: Manual test when the self-test finds nothing; fuel level requirement
- [6] Hyundai TSB — Accent canister close valve inspection (via NHTSA) — used for: A second manufacturer's EVAP valve procedure
Other code guides
- P0420: Catalyst System Efficiency Below Threshold (Bank 1)
- P0300: Random/Multiple Cylinder Misfire Detected
- P0171: System Too Lean (Bank 1)
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)
- P0442: Evaporative Emission System Leak Detected (Small Leak)
- P0456: Evaporative Emission System Leak Detected (Very Small Leak)
- P0174: System Too Lean (Bank 2)
- P0301: Cylinder 1 Misfire Detected
- P0430: Catalyst System Efficiency Below Threshold (Bank 2)