OBD2 Code Guide: Definitions, Causes & Diagnosis
By Roger Holden. Updated November 10, 2026.
A trouble code tells you which test the engine computer failed, not which part to buy. Each guide gives the code's standard description, how the computer decides to set it, the causes worth ruling out in order, and when to stop driving, with sources for every one.
We check each code's wording against manufacturer service bulletins published by NHTSA and take monitor behavior from California's OBD II regulation. Diagnostic steps follow the order manufacturers give technicians: gather the evidence, fix related codes first, check for bulletins and software, then test the suspected part.
Code guides
- P0420: Catalyst System Efficiency Below Threshold (Bank 1) — Severity: Moderate. The computer judged the bank 1 catalytic converter is no longer cleaning exhaust well enough. Misfires, fuel-mixture faults and sensor problems have to be ruled out first.
- P0300: Random/Multiple Cylinder Misfire Detected — Severity: High. Misfires were detected across more than one cylinder, or the computer couldn't pin them to one. A flashing light means the misfire can damage the catalytic converter.
- P0171: System Too Lean (Bank 1) — Severity: Moderate. The computer added as much fuel as it's allowed to on bank 1 and the mixture still read lean. Unmetered air, a dirty airflow sensor and weak fuel delivery are the usual suspects.
- P0455: Evaporative Emission System Leak Detected (Large Leak) — Severity: Low to moderate. The fuel-vapor system failed to hold its test pressure or vacuum. Start with the fuel cap; stuck valves and split hoses come next.
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) — Severity: Low to moderate. The engine took too long to warm up, or didn't reach its normal operating temperature. A thermostat stuck open is the usual cause, but check the coolant level and sensor first.
- P0442: Evaporative Emission System Leak Detected (Small Leak) — Severity: Low to moderate. The fuel-vapor system failed its small-leak test. Record the diagnostic evidence, then check the cap, vapor-line connections and valve sealing before replacing parts.
- P0456: Evaporative Emission System Leak Detected (Very Small Leak) — Severity: Low to moderate. The fuel-vapor system failed its very-small-leak check. Cap sealing, a canister close valve or vehicle-specific leak-detection hardware can be involved; testing decides which.
- P0174: System Too Lean (Bank 2) — Severity: Moderate. The computer detected a lean fuel-system condition on bank 2. Check intake and PCV connections, applicable software guidance, fuel delivery and sensor function before replacing parts.
- P0301: Cylinder 1 Misfire Detected — Severity: High. The computer detected a misfire on cylinder 1. Test that cylinder’s ignition, injector and compression; a flashing light warns of possible catalyst damage.
- P0430: Catalyst System Efficiency Below Threshold (Bank 2) — Severity: Moderate. The catalyst monitor failed on bank 2. Identify the correct bank, check related faults and software, and rule out exhaust leaks before replacing parts.
How to read any OBD2 code
Generic codes have five characters. The letter names the system: P for powertrain, B for body, C for chassis and U for network communication. A 0 as the second character marks a generic code defined by the SAE J2012 standard; a 1 usually marks a manufacturer-specific code. The last three characters identify the fault.
Most emissions faults store a pending code the first time and a confirmed code, with the check engine light, if they're seen again on the next drive cycle in which the test runs. Under California's rules, the light turns off after three consecutive drive cycles without the fault. A light that goes out isn't proof of a repair.
Record stored, pending and permanent codes and available freeze-frame data before clearing anything. Clearing codes does not fix the fault; it can erase useful evidence and reset emissions readiness monitors.
Start with the check engine light assistant or read how to use an OBD2 scanner.